Disciplina temática
Ingeniería mecánica
Artículos (134) Publicaciones en las que ha participado algún/a investigador/a
2019
-
(ρ, VE, T) Measurements of the Ternary Mixture (Dibutyl Ether + 1-Heptanol + Heptane) at Temperatures up to 393.15 K and Pressures up to 140 MPa and Modeling Using the Peng-Robinson and PC-SAFT Equations of State
Journal of Chemical and Engineering Data, Vol. 64, Núm. 9, pp. 3861-3873
-
3D Tdoa problem solution with four receiving nodes
Sensors (Switzerland), Vol. 19, Núm. 13
-
A Bayesian Networks approach for the assessment of climate change impacts on nutrients loading
Environmental Science and Policy, Vol. 100, pp. 21-36
-
A Simplified method to minimize exterior girder rotation of steel bridges during deck construction
Engineering Structures, Vol. 183, pp. 84-93
-
A fault detection system for a geothermal heat exchanger sensor based on intelligent techniques
Sensors (Switzerland), Vol. 19, Núm. 12
-
A hybrid SURF-DIC algorithm to estimate local displacements in structures using low-cost conventional cameras
Engineering Failure Analysis, Vol. 104, pp. 807-815
-
A laser and video-based displacement transducer for the monitoring of bridge deflections
Review of progress in quantitative nondestructive evaluation, pp. 1-4
-
A look to the electricity generation from non-conventional renewable energy sources in Colombia
International Journal of Energy Economics and Policy, Vol. 9, Núm. 1, pp. 15-25
-
A novel technique based in a cylindrical microwave resonator for high pressure phase equilibrium determination
Journal of Chemical Thermodynamics, Vol. 135, pp. 124-132
-
A systematic FEM analysis of the influence of mechanical properties in the reliability of the correlation methods in the small punch test
International Journal of Mechanical Sciences, Vol. 153-154, pp. 299-309
-
Academic proposal for heritage intervention in a BIM environment for a 19th century flour factory
Applied Sciences (Switzerland), Vol. 9, Núm. 19
-
Accuracy analysis in sensor networks for asynchronous positioning methods
Sensors (Switzerland), Vol. 19, Núm. 13
-
An incremental-iterative BEM methodology to solve 3D thermoelastic contact problem including variable thermal resistance in the contact zone
Continuum Mechanics and Thermodynamics, Vol. 31, Núm. 5, pp. 1543-1558
-
Analysis of Spanish Radiometric Networks with the Novel Bias-Based Quality Control (BQC) Method
Sensors (Basel, Switzerland), Vol. 19, Núm. 11
-
Analysis of a single-edge micro cutting process in a hybrid parallel-serial machine tool
International Journal of Mechanical Sciences, Vol. 151, pp. 222-235
-
Analysis of musts and wines by means of a bio-electronic tongue based on tyrosinase and glucose oxidase using polypyrrole/gold nanoparticles as the electron mediator
Food Chemistry, Vol. 289, pp. 751-756
-
Analysis of the Influence of the Thickness and the Hole Radius on the Calibration Coefficients in the Hole-Drilling Method for the Determination of Non-uniform Residual Stresses
Experimental Mechanics, Vol. 59, Núm. 1, pp. 79-94
-
Analysis of the methodology to obtain several key indicators performance (KIP), by energy retrofitting of the actual building to the district heating fuelled by biomass, focusing on nZEB goal: Case of study
Energies, Vol. 12, Núm. 1
-
Application of the hole-drilling method for the evaluation of residual stresses near rounded ends
Journal of Strain Analysis for Engineering Design, Vol. 54, Núm. 7-8, pp. 424-430
-
Assessment of emerging risk level by occupational exposure to hand-arm vibrations: Approach under uncertainty conditions
Safety Science, Vol. 114, pp. 140-147